Student Diggs in Huddersfield

1. Student Diggs in Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/student-diggs-huddersfield

2. Axle Bearings

Because axle shafts are typically made of softer steel than bearing rollers, shafts have a tendency to wear out before the bearing. The rollers can actually wear away a section of the shaft, as shown in the below diagram. Automotive cylindrical axle repair bearings are designed to replace the original bearings and seals on axles that are still in good condition, but whose original bearing and/or seal contact paths are not suitable for continued use. The extra-wide bearing repositions the rollers and seal to ride on unworn portions of the axle closer to the flange. Lubrication is accomplished through the axle tube by differential fluid, just like the OE design.

http://ball-bearings.online

3. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.custom.software.grid-itc.com

4. Huddersfield University Student Accomodation

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://huddersfield-university-student-accomodation.iam4rent.co.uk/

5. Plain Bearings

Plain bearings. Spherical plain bearings are standardized, ready-to-mount mechanical components that are self-aligning and enable multi-directional alignment movements to be made. The inner ring has a sphered convex outside diameter and the outer ring has a correspondingly sphered but concave inside surface. Rod ends are bearing units that consist of a spherical plain bearing in an eye-shaped head with integral shank - the rod end housing. They are used primarily on the ends of piston rods or together with hydraulic as well as pneumatic cylinders to join the cylinder to associated components. Spherical plain bearings are standardized, ready-to-mount, mechanical components that enable multi-directional, self-aligning movements. The inner ring has a spherical convex outside diameter, while the outer ring has a correspondingly concave inside diameter. The forces acting on the bearing may be static or may occur when the bearing makes oscillating or recurrent tilting and slewing movements at relatively low speeds.

http://ball-bearings.online

6. Stainless Steel Flange Gaskets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

7. Stainless Steel Valves

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://valves.stainless-steel.zx55.com

8. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://abrt.com/bespoke-software

9. IT Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.1t-s.com/service

10. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.software.development.1t-s.com

11. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://abrt.com/application-development

12. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-steel.ktforge.co.uk

13. Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://open-source.1t-s.com

14. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.software.devlopment.abrt.com

15. Salaat Times

Salaat Times, Salah Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.

http://salaat-times.jamat-times.com

16. Sheffield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.bespoke-software.1tsolutions.com

17. Free Accounts Software

Download Ice Ledger accounts system now for free and get started. Fully featured, multi-currency accounts with Sales, Purchase and Nominal ledgers, Sales and Purchase Invoicing, Stock Control and more...

http://iceledger.com/

18. Smith Forging

Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.

http://smith-forging.kt-forge.co.uk

19. Rotherham Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.application.development.1t-s.com

20. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.grid-itc.com/custom-software

21. Low Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://low-pressure-fittings.stainless-steel.zx55.com

22. Chesterfield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.application.development.grid-itc.com

23. Online Bearings

Online Bearings. Totally refreshing concept to the way you purchase your bearings and power transmission products. With experience in the bearing industry, we aim to provide the best quality product at the best possible price. We carry from stock all types of bearings, including deep groove ball bearings, roller bearings, metric and imperial bearings, tapered roller bearings, spherical bearings and needle bearings - plus many more. We also stock all types of chains and sprockets, taper bushes, oil seals and O-rings, airline fittings, braided hose, oils, greases and lubricants, as well as all types of lubrication equipment. In addition, we supply industrial tools, V-belts and wedge belts, timing belts and HTD belts and also offer a belt making service for all types of flat belts. Our preferred brands of bearings and power transmission products are from leading manufacturers, but we have an extensive range of cheaper alternatives in our budget section for customers who wish to keep their costs to a minimum.

http://ball-bearings.online

24. Skip Manager

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.skip-manager.com

25. Taper Bearings

Tapered roller bearings are bearings that can take large axial forces (i.e., they are good thrust bearings) as well as being able to sustain large radial forces. The inner and outer ring raceways are segments of cones and the rollers are also made with a taper so that the conical surfaces of the raceways and the roller axes if projected, would all meet at a common point on the main axis of the bearing. This conical geometry is used as it gives a larger contact patch, which permits greater loads to be carried than with spherical (ball) bearings, while the geometry means that the tangential speeds of the surfaces of each of the rollers are the same as their raceways along the whole length of the contact patch and no differential scrubbing occurs. When a roller slides rather than rolls, it can generate wear at the roller-to-race interface, i.e. the differences in surface speeds creates a scrubbing action. Wear will degenerate the close tolerances normally held in the bearing and can lead to other problems. Much closer to pure rolling can be achieved in a tapered roller bearing and this avoids rapid wear. The rollers are guided by a flange on the inner ring. This stops the rollers from sliding out at high speed due to their momentum. The larger the half angles of these cones the larger the axial force that the bearing can sustain. Tapered roller bearings are separable and have the following components: outer ring, inner ring, and roller assembly (containing the rollers and a cage). The non-separable inner ring and roller assembly is called the cone, and the outer ring is called the cup. Internal clearance is established during mounting by the axial position of the cone relative to the cup.

http://ball-bearings.online

26. Stainless Steel Flange Gaskets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.flange-gaskets.stainless-steel.zx55.com

27. Chesterfield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.bespoke-software.1tsolutions.com

28. British Leyland Car Bearings

British Leyland was a British automotive company formed in 1968 through the merger of several British automobile manufacturers, including British Motor Corporation (BMC) and Leyland Motors. British Leyland was created on January 17, 1968, as a state-owned entity with the aim of consolidating the British automotive industry. It brought together various well-known British brands, including Austin, Morris, MG, Triumph, Jaguar, Rover, and Land Rover. In 1986, the British government privatized British Leyland, and the company was renamed Rover Group. In 1988, British Aerospace acquired the Rover Group, and later, in 1994, BMW purchased Rover Group. Under BMW's ownership, the Rover Group faced challenges, including financial losses and a lack of synergy with the BMW brand. In 2000, BMW decided to sell the Rover Group, and the MG Rover consortium, consisting of several British businessmen, acquired it. However, MG Rover faced ongoing financial difficulties, and in 2005, the company entered administration, leading to the end of MG Rover production.

http://ball-bearings.online/oem/briley/products

29. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://bespoke.software.1t-s.com

30. SKF Energy Efficient (E2) deep groove ball bearings

The new SKF Energy Efficient deep groove ball bearings are designed to improve machine efficiency and to save energy, see presentation Energy Efficient solutions. These bearings belong to SKF E2 performance class family, providing: optimized internal geometry for reduced friction, a shield on both sides to protect the friction-reducing features, new cage design, unique lubricant, The designation follows the basic SKF designation system. To clearly show the new performance the prefix "E2." has been added. SKF Energy Efficient bearings are supplied in a new standard box.

http://ball-bearings.online?pg=rb-dgbb-e2

31. Chesterfield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.bespoke.software.1t-s.com

32. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://grid-itc.com/custom-software

33. Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/steel-forging

34. Chesterfield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.application.development.grid-itc.com

35. Cold Forming

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://cold-forming.kt-forge.co.uk

36. Forging Stainless Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-stainless-steel.ktforge.co.uk

37. Doncaster Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.application.development.grid-itc.com

38. Barnsley Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://barnsley.web-design.1t-s.com

39. Barnsley Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.custom-software.1tsolutions.com

40. Computer Repair

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://abrt.com/computer-repair

41. Chesterfield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.bespoke-software.1tsolutions.com

42. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://www.ktforge.co.uk/open-die-forging

43. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://1tsolutions.com/custom-software

44. Rotherham Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://rotherham.computer.service.1t-s.com

45. Car Wheel Bearings

Checking a car's Wheel Bearings. You can check your car's wheel bearings to see if they need to be repacked. Wheel bearings usually come in pairs of inner and outer bearings. They allow your wheels to turn freely over thousands of miles by cushioning the contact between the wheel and the spindle it sits on with frictionless bearings and lots of nice, gooey grease. This grease tends to pick up dust, dirt, and little particles of metal, even though the bearings are protected to some extent by the hub and the brake drum or disc. Usually, only the non-drive wheels (that is, the front wheels on rear-wheel drive vehicles and the rear wheels on front-wheel drive vehicles) have repackable wheel bearings. Vehicles with front-wheel drive have sealed front bearings, but some have packable rear ones. The bearings on four-wheel drive vehicles are quite complicated and should be repacked professionally. Before you check your bearings, consult your owner's manual or dealership to find out whether the bearings on your vehicle are sealed. If they are, you can't repack them. If you have drum brakes: It's important to check the bearings when you check your brakes to make sure that the grease hasn't become fouled. If it has, the particles act abrasively to wear away the very connection the bearings are designed to protect, and the result is a noisy, grinding ride. In extreme cases, you could even lose the wheel! If the bearings look cruddy, either repack them yourself or get a professional to do it. If you have disc brakes: You have to remove the caliper to get at the bearings. Although this task isn't terribly difficult, certain aspects of the job can create problems for a beginner. Because your brake system can kill you if it isn't assembled properly, you might want to do the job under supervision at an auto class.

http://ball-bearings.online

46. Rotherham Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.software.devlopment.grid-itc.com

47. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://open-die-forging.ktforge.co.uk

48. Stainless steel deep groove ball bearings

SKF stainless steel deep groove ball bearings are resistant to corrosion from moisture and several other media. These single row deep groove ball bearings have the same deep raceway grooves and close conformity between raceways and balls as standard deep groove ball bearings made of carbon chromium (rolling bearing) steel. They are without filling slots and can carry axial loads acting in both directions in addition to radial loads, even at high speeds. SKF stainless steel deep groove ball bearings have the same running properties as conventional steel deep groove ball bearings, but have a lower load carrying capacity. The bearings are available in open and sealed designs for shaft diameters from 1 to 50 mm. SKF stainless steel bearings are identified by the designation prefix W, e.g. W 626-2Z.

http://ball-bearings.online?pg=rb-dgbb-ss

49. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.custom.software.1t-s.com

50. Angular Contact Bearings

Angular contact ball bearings. Angular contact ball bearings have raceways in the inner and outer rings that are displaced with respect to each other in the direction of the bearing axis. This means that they are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads. The axial load carrying capacity of angular contact ball bearings increases with increasing contact angle. The contact angle a is defined as the angle between the line joining the points of contact of the ball and the raceways in the radial plane, along which the load is transmitted from one raceway to another, and a line perpendicular to the bearing axis. SKF angular contact ball bearings are produced in a wide variety of designs and sizes. Those commonly used and included in this catalogue are: single row angular contact ball bearings; double row angular contact ball bearings; four-point contact ball bearings.

http://ball-bearings.online?pg=rb-acbb

51. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.custom.software.abrt.com

52. Stainless Steel Gaskets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

53. Stainless Steel Low Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

54. Deep groove ball bearings with filling slots

Single row deep groove ball bearings with filling slots have a filling slot in both the inner and outer ring enabling more and larger balls to be incorporated than in standard deep groove ball bearings. Filling slot bearings have a higher radial load carrying capacity than bearings without filling slots, but their axial load carrying capacity is small. They are also unable to operate at such high speeds as bearings without filling slots. Depending on the main application for which they are used, deep groove ball bearings with filling slots have a cage or no cage.

http://ball-bearings.online?pg=rb-dgbb-fs

55. Doncaster Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.doncaster.software.devlopment.1tsolutions.com

56. Forging Stainless Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-stainless-steel.kt-forge.co.uk

57. Stainless Steel Butt-Weld Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.butt-weld-fittings.stainless-steel.zx55.com

58. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://house-for-rent-huddersfield.iam4rent.co.uk/

59. Chesterfield Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.chesterfield.linux.1t-s.com

60. Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://web-design.1t-s.com

61. Student Housing Huddersfield

4 Bedroom student housing to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.student-housing-huddersfield.co.uk/

62. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.application.development.abrt.com

63. Chesterfield Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://chesterfield.linux.1t-s.com

64. Skip Manager

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://skip-manager.co.uk

65. Student Accomodation Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://student-accomodation-huddersfield.iam4share.co.uk/

66. Sheffield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.bespoke.software.abrt.com

67. South Yorkshire Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.south-yorkshire.bespoke.software.grid-itc.com

68. Rotherham Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.custom.software.1t-s.com

69. Upset Forging

Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.

http://upset-forging.ktforge.co.uk

70. Doncaster Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://doncaster.computer.service.1t-s.com

71. Doncaster Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.doncaster.bespoke.software.abrt.com

72. Barnsley Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.custom-software.1tsolutions.com

73. Skip Hire Software

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.skip-hire-software.com

74. Hot Forming

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://hot-forming.kt-forge.co.uk

75. Sheffield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.custom-software.1tsolutions.com

76. Cold Forming

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://www.kt-forge.co.uk/cold-forming

77. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-steel.kt-forge.co.uk

78. Stainless Tube Supplier

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

79. Hammer Forging

The most common type of forging equipment is the hammer and anvil. Principles behind the hammer and anvil are still used today in drop-hammer equipment. The principle behind the machine is simple: raise the hammer and drop it or propel it into the workpiece, which rests on the anvil. The main variations between drop-hammers are in the way the hammer is powered; the most common being air and steam hammers. Drop-hammers usually operate in a vertical position. The main reason for this is excess energy (energy that isn't used to deform the workpiece) that isn't released as heat or sound needs to be transmitted to the foundation. Moreover, a large machine base is needed to absorb the impacts. To overcome some shortcomings of the drop-hammer, the counterblow machine or impactor is used. In a counterblow machine both the hammer and anvil move and the workpiece is held between them. Here excess energy becomes recoil. This allows the machine to work horizontally and have a smaller base. Other advantages include less noise, heat and vibration. It also produces a distinctly different flow pattern. Both of these machines can be used for open-die or closed-die forging. A forging press, often just called a press, is used for press forging.

http://www.ktforge.co.uk/hammer-forging

80. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://application-development.1tsolutions.com

81. Sockolets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

82. Student Accomodation in Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/student-accomodation-huddersfield

83. Chesterfield Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://chesterfield.web-design.1t-s.com

84. Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.grid-itc.com/computer-services

85. Sheffield Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.sheffield.computer.service.1t-s.com

86. Doncaster Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.custom-software.1tsolutions.com

87. South Yorkshire Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.south-yorkshire.computer.service.1t-s.com

88. Waste Collection Software

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://waste-collection-software.skip-manager.co.uk

89. Stainless Pipe Supplier

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

90. Sheffield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.custom-software.1tsolutions.com

91. Forging Stainless Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/forging-stainless-steel

92. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.software.devlopment.abrt.com

93. Sheffield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.application.development.1t-s.com

94. Bankrupt Bearings

We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.

http://www.surplus-bearings.co.uk

95. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1tsolutions.com/custom-software

96. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.custom-software.1tsolutions.com

97. Chesterfield Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.chesterfield.open-source.1t-s.com

98. Chesterfield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.bespoke.software.abrt.com

99. South Yorkshire Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.bespoke-software.1tsolutions.com

100. IT Support

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.1t-s.com/service

101. Hot Forging

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://www.ktforge.co.uk/hot-forging

102. Drop Forging

Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.

http://drop-forging.ktforge.co.uk